Evak Hippo 65-150 1.1kW DN65 Sewage Pump 230V

Name: Evak Hippo 65-150 1.1kW DN65 Sewage Pump 230V
Brand: EVAK
SKU: evakhippo65-150.230
Price: 567.6 GBP
Availability: InStock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

The Evak Hippo 65-150 (230V) is the entry point to the Hippo DN65 range — the step up from the 2″ Hippo 50 series to a 65 mm free passage sewage pump with a DN65 flanged discharge for guide rail installation. 1.1 kW / 1.5 HP single-phase motor, recessed vortex impeller, up to 600 L/min and 11 m of head.

Built for raw sewage, soiled wastewater and heavy rainwater in pump stations, packaged sewage chambers and commercial drainage. The 65 mm passage takes the solids and rag a 50 mm pump blocks on. Cast iron pump body, stainless steel motor housing, EKK Eagle Burgmann double mechanical seal. Internal capacitor and 10 m cable; float switch available.

1.1 kW

Motor output

600 L/min

Max flow

11 m

Max head

65 mm

Free passage

230V single-phase
DN65 flanged
Guide rail ready
Vortex impeller
Eagle Burgmann seal
IP68

Entry-level DN65 — 1.5 HP, 230V. Flanged outlet: this pump is designed for a QD-65 guide rail coupling or a flanged riser, not a threaded hose tail — for a free-standing 2″ threaded pump see the Hippo 50 series. Also available as the Hippo 65-150 400V. For more flow see the 65-200 (1.5 kW, 720 L/min, 13 m).

Full Description

More about this product

Full Description

The Evak Hippo 65-150 (230V) is the smallest pump in the Hippo DN65 range, and the point at which the Hippo family stops being a free-standing drainage pump and becomes a pump-station pump. The model code says it: 65 for the 65 mm discharge and free passage, 150 for 1.5 HP. A 1.1 kW 2-pole single-phase motor drives a recessed vortex impeller to 600 L/min and 11 m of head, with a rated duty of 330 L/min at 6.6 m — the working point for a typical domestic or small commercial sewage chamber.

The 65 mm free passage is the reason to buy it over a 50 mm pump. Raw sewage carries rag, wipes and solids that wrap around a smaller impeller; the DN65 vortex design keeps the impeller recessed out of the flow so solids pass through the volute without touching it. The DN65 flanged discharge (DIN PN10/16) bolts to a QD-65 quick-discharge coupling for guide rail installation, so the pump lifts out for service without anyone entering the chamber.

Cast iron pump body and volute, stainless steel motor housing, and an EKK Eagle Burgmann double mechanical seal (carbon/ceramic upper, silicon carbide lower) in an oil bath with NBR lip seal. Class F insulation, IP68, auto-reset thermal protector, ball bearings. Internal capacitor, 10 m cable. Supplied manual; a float switch version is available for automatic single-pump duty.

Key features

1.1 kW

Motor output

1.5 HP

Horsepower

10 A

FLA @ 230V

DN65

Flanged discharge

65 mm

Free passage

600 L/min

Max flow

11 m

Max head

30.7 kg

Weight

Performance

Flow (L/min)	0	100	200	300	330	400	500	600
Head (m)	11.0	10.0	8.8	7.3	6.6	5.6	4.2	3.0

50 Hz, 2850 rpm. 330 L/min @ 6.6 m is the Evak rated duty point; other values read from the published curve.

Construction

65 mm vortex impeller

Recessed vortex design passes 65 mm solids and rag through the volute without contact — the difference between a sewage pump that blocks and one that doesn’t.

DN65 flanged discharge

DIN PN10/16 flange for a QD-65 quick-discharge coupling on a guide rail, or direct to a flanged riser. Lift out for service without entering the chamber.

Cast iron pump body

FC200 cast iron volute and casing for long life in raw sewage.

Stainless motor housing

Stainless steel motor housing over a Class F dry-type motor with auto-reset thermal protector and ball bearings. IP68.

EKK Eagle Burgmann double seal

Carbon/ceramic upper and silicon carbide lower mechanical seals in an oil bath with NBR lip seal — a named, serviceable seal set, not a generic one.

Single-phase with internal capacitor

Start capacitor built into the motor — no external box. Runs from a panel or, with the float switch option, on its own.

Applications

Packaged sewage pump stations

Single or duty/standby pumps in below-ground chambers serving houses, small developments and outbuildings below the sewer level.

Commercial wastewater

Pubs, restaurants, care homes and small commercial premises where rag and wipes rule out a 50 mm pump.

Septic tank & treatment plant transfer

Pumping settled effluent or raw influent between tanks and to soakaways where the site falls the wrong way.

Surface & rainwater

Heavy rainwater and surface water drainage carrying leaves and debris.

Replacement duty

Direct swap for existing DN65 guide rail pumps — check the coupling and rail centres before ordering.

Maximum liquid temperature 40 °C. Maximum submersion 10 m. Maximum 20 starts per hour. Flanged discharge — order the QD-65 coupling or a flange adaptor with the pump. Supplied manual; specify the float switch version for automatic single-pump duty. Not for potable water or corrosive fluids (see Stainox range). Three-phase site? See the Hippo 65-150 400V. For more flow see the 65-200 (1.5 kW) or the 76 mm passage Hippo 80 series.

Technical specifications

Model	Evak Hippo 65-150 (HIPPO-150 DN65), 230V
Series	Evak Hippo DN — 2.5″ full free passage submersible sewage pump
Voltage / phase	230V single-phase, 50 Hz
Motor output	1.1 kW (1.5 HP)
Full load current	10 A
Starting	Internal capacitor
Poles / speed	2 pole / 2850 rpm
Operation	Manual (float switch version available)
Discharge	DN65 (2.5″) flanged, DIN PN10/16
Free passage	65 mm
Rated duty	330 L/min @ 6.6 m
Max head	11 m
Max flow rate	600 L/min
Max liquid temperature	40 °C
Max submersion depth	10 m
Max starts per hour	20
Protection / insulation	IP68 / Class F
Thermal protection	Auto-reset thermal protector
Bearings	Ball type
Impeller	Recessed vortex
Pump casing	FC200 cast iron
Motor housing	Stainless steel
Mechanical seal	EKK Eagle Burgmann double mechanical, upper Ca/Ce, lower SiC/SiC, oil bath with NBR lip seal
Guide rail coupling	QM-65 / QD-65 (sold separately)
Cable	H07RN-F, 10 m
Overall height	580 mm
Weight (without cable)	30.7 kg

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.

Frequently Asked Questions

Quick answers to common questions about the Evak Hippo 65-150 1.1kW DN65 Sewage Pump 230V. For technical specifications, see the product details above; for sizing or installation advice, contact our team. If you have any other questions, we're happy to help.

What is a submersible pump?

A submersible pump is designed to operate fully submerged in the liquid it is moving. The motor is sealed inside the pump body and cooled by the surrounding water. Submersibles are used for drainage, sewage, septic tanks, deep wells and boreholes, and for raising water from sumps, cellars and floodwater. Many stocked at Anglian Pumping handle solids in suspension.

Can submersible pumps handle solids and sewage?

Yes – some submersibles are designed for clean water only, others handle solids up to 50 mm or full raw sewage. Anglian Pumping stocks ABS, BBC, Flygt and T-T Submersibles ranges that include vortex, single channel and grinder impellers for different solids handling requirements. Always match the pump to the maximum solid size and the type of effluent it will see.

When should I use a submersible pump instead of a surface pump?

Use a submersible when the water level is more than around 8 metres below the pump installation point – surface pumps cannot self-prime beyond that depth. Submersibles are also better when the liquid contains solids, when noise must be minimised, or when the pump needs to operate in confined spaces such as sumps and chambers where a surface pump would not fit.