Grundfos SQE Pumps
Grundfos CU 301 Constant Pressure Package 96524504
- Established 1975
- Trusted by thousands of customers
The Grundfos CU 301 Constant Pressure Package (96524504) turns any Grundfos SQE borehole pump into a constant-pressure water system. The CU 301 reads a pressure sensor and changes the speed of the SQE to hold a steady pressure at the taps, from 2 to 5 bar, however many outlets are open. It talks to the pump over the existing power cable, so no extra wire goes down the borehole. The package includes the controller, sensor, an 8-litre diaphragm vessel, a gauge and an isolating valve. The pump is sold separately.
No extra pump cable
Dry-run alarm
100–240V
2-year warranty
More about this product
Grundfos CU 301 constant pressure package overview
A standard borehole pump runs flat out and is switched on and off by a pressure switch, so the pressure at the taps rises and falls with every cycle. The CU 301 does the job differently. It reads the system pressure from its sensor and tells the Grundfos SQE pump to speed up or slow down, so the pressure holds at the level you set. One shower or three outlets at once, the pressure stays the same.
The CU 301 talks to the SQE’s MSE3 motor over the existing pump power cable, so no signal wire goes down the borehole. It also shows the pump’s status and alarms on the front panel and stops the pump when there is no demand. This package includes everything needed at the surface. Add the SQE pump that suits your borehole, plus drop cable and a joint kit.
What’s in the package
| Item | Detail |
|---|---|
| CU 301 control unit | Pressure display in bar, on/off and adjustment buttons, alarm indication |
| Pressure sensor | 0–6 bar, 4–20 mA |
| Diaphragm vessel | 8 litre (GT-H-8), 10 bar |
| Pressure gauge | 0–10 bar, 63 mm dial |
| Isolating valve | ¾” ball valve |
| Cable clips | 20 pcs, for fixing drop cable to the rising main |
| Not included | SQE pump, drop cable, cable joint kit, rising main and pipe fittings |
Key features
Technical specification (CU 301)
| Package part number | Grundfos 96524504 |
| Compatible pumps | Grundfos SQE (MSE3 motor) |
| Supply | 1 × 100–240V −10%/+6%, 50/60 Hz, PE |
| Back-up fuse | Max. 16 A |
| Power consumption | 5 W (max. 130 mA) |
| Pressure setting | 2.0–5.0 bar in 0.5 bar steps (factory setting 3.0 bar) |
| Sensor input | 0–10 V, 2–10 V, 0–20 mA or 4–20 mA; max. sensor cable 500 m |
| Pump communication | Mains-borne signalling over the pump power cable |
| Max. cable length, CU 301 to pump | 200 m |
| Pump speed range | 3,000–10,700 rpm |
| Max. conductor size | 6 mm² (mains and pump terminals) |
| Enclosure class | IP55 |
| Ambient temperature | −30 to +50 °C in operation (keep out of direct sunlight) |
| Max. relative humidity | 95% |
| CU 301 weight | 2.0 kg |
| Warranty | 2 years |
Vessel pre-charge
Set the diaphragm vessel’s air pre-charge to 70% of the CU 301 pressure setting, and check it with the system drained down. If the pre-charge is higher than the setting, the CU 301 can’t control the pressure.
| CU 301 setting (bar) | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 |
|---|---|---|---|---|---|---|---|
| Vessel pre-charge (bar) | 1.4 | 1.8 | 2.1 | 2.5 | 2.8 | 3.2 | 3.5 |
Installation notes
- Mount the CU 301 indoors or under cover, out of direct sunlight, within 200 m of cable run from the pump.
- Wire the mains supply and the pump cable straight into the CU 301. No separate pump control box or pressure switch is needed.
- Fit the pressure sensor, gauge and 8-litre vessel together on the outlet pipework after the isolating valve. Keep the sensor close to the vessel for stable control.
- Choose the pump for your set point. Add at least 20 m of head (2 bar) to your water level, rise and pipe losses, and check the SQE can deliver your flow at that total.
- If you’ll change the set point later, set the pre-charge for the lowest setting you’ll use. Grundfos suggests fitting a larger vessel in that case.
CU 301 constant pressure package FAQs
-
sales Sheet PDFDownload
-
CU301 data PDFDownload
-
CU301 wiring PDFDownload
Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.
Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).
Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.
Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.
Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.
You may also need
Accessories for Grundfos SQ and SQE pumps Heat shrink cable joint, 3 x 1.5-2.5mm 96023762
Accessories for Grundfos SQ and SQE pumps Constant pressure package including – CU301 control box, GT-H-8 8 litre vessel, 4-20mA pressure transducer, 0-10 pressure gauge,…
Accessories for Grundfos SQ and SQE pumps Drop cable 3 x 2.5mm per metre 00ID7947
Accessories for Grundfos SQ and SQE pumps CU301 control box commerical 96436753



