Evak Hippo 65-300 2.2kW DN65 Sewage Pump 400V

Name: Evak Hippo 65-300 2.2kW DN65 Sewage Pump 400V
Brand: EVAK
SKU: evakhippo65-300400
Price: 681.6 GBP
Availability: InStock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

The Evak Hippo 65-300 (400V) is where the Hippo DN65 range goes three-phase only. 2.2 kW / 3 HP motor, recessed vortex impeller, 65 mm free passage and a DN65 flanged discharge for guide rail installation. 870 L/min and 17 m of head — a 4 m jump over the 65-200 for longer rising mains and deeper chambers.

Built for raw sewage, soiled wastewater and heavy rainwater in pump stations serving developments, commercial premises and treatment plants. The 65 mm passage takes the solids and rag a 50 mm pump blocks on. Cast iron pump body, stainless steel motor housing, EKK Eagle Burgmann double mechanical seal. Manual operation for panel control. 10 m cable.

2.2 kW

Motor output

870 L/min

Max flow

17 m

Max head

65 mm

Free passage

400V three-phase
Manual operation
DN65 flanged
Guide rail ready
Eagle Burgmann seal
IP68

Three-phase only — 3 HP, 6 A at 400V. No single-phase version. Needs a control panel with level control. Flanged outlet for a QD-65 guide rail coupling or flanged riser, not a hose tail. For single-phase see the 65-200 230V. For more see the 65-400 (3 kW, 1,000 L/min, 20 m).

Full Description

More about this product

Full Description

The Evak Hippo 65-300 (400V) is the first of the three-phase-only Hippo DN65 models and the point where the range moves from domestic pump stations to commercial ones. The model code says it: 65 for the 65 mm discharge and free passage, 300 for 3 HP. A 2.2 kW 2-pole motor drives a recessed vortex impeller to 870 L/min and 17 m of head, with a rated duty of 300 L/min at 12.6 m — the extra head is the story here: 4 m more than the 65-200 for the same free passage, which opens up rising mains that the smaller pumps can’t reach.

The 65 mm free passage is the reason to buy it over a 50 mm pump. Raw sewage carries rag, wipes and solids that wrap around a smaller impeller; the DN65 vortex design keeps the impeller recessed out of the flow so solids pass through the volute without touching it. The DN65 flanged discharge (DIN PN10/16) bolts to a QD-65 quick-discharge coupling for guide rail installation, so the pump lifts out for service without anyone entering the chamber.

Cast iron pump body and volute, stainless steel motor housing, and an EKK Eagle Burgmann double mechanical seal (carbon/ceramic upper, silicon carbide lower) in an oil bath with NBR lip seal. Class F insulation, IP68, auto-reset thermal protector, ball bearings. Three-phase motor drawing 6 A, no capacitor, no float — supplied manual for control from a panel. 10 m cable. 34 kg.

Key features

2.2 kW

Motor output

3 HP

Horsepower

6 A

FLA @ 400V

DN65

Flanged discharge

65 mm

Free passage

870 L/min

Max flow

17 m

Max head

34 kg

Weight

Performance

Flow (L/min)	0	100	200	300	400	500	600	700	800	870
Head (m)	17.0	16.0	14.6	12.6	11.0	9.2	7.4	5.6	4.0	3.0

50 Hz, 2850 rpm. 300 L/min @ 12.6 m is the Evak rated duty point; other values read from the published curve.

Construction

65 mm vortex impeller

Recessed vortex design passes 65 mm solids and rag through the volute without contact — the difference between a sewage pump that blocks and one that doesn’t.

DN65 flanged discharge

DIN PN10/16 flange for a QD-65 quick-discharge coupling on a guide rail, or direct to a flanged riser. Lift out for service without entering the chamber.

Cast iron pump body

FC200 cast iron volute and casing for long life in raw sewage.

Stainless motor housing

Stainless steel motor housing over a Class F dry-type motor with auto-reset thermal protector and ball bearings. IP68.

EKK Eagle Burgmann double seal

Carbon/ceramic upper and silicon carbide lower mechanical seals in an oil bath with NBR lip seal — a named, serviceable seal set, not a generic one.

Three-phase manual motor

400V three-phase, 6 A, no capacitor, no float — wired to a control panel with level probes or floats. The right motor for duty/standby stations.

Applications

Duty/standby pump stations

Twin-pump sewage chambers serving developments, apartment blocks and commercial sites, run from a panel with alternating duty.

Long rising mains

17 m of head for pumped mains to a distant or elevated sewer connection where the 2 HP pumps run out of lift.

Commercial wastewater

Hotels, schools, leisure centres and care homes where rag and wipes rule out a 50 mm pump.

Treatment plant transfer

Pumping raw influent or settled effluent between tanks on larger packaged treatment plants.

Replacement duty

Direct swap for existing DN65 guide rail pumps — check the coupling and rail centres before ordering.

Maximum liquid temperature 40 °C. Maximum submersion 10 m. Maximum 20 starts per hour. Manual operation — no float switch fitted. Three-phase only; requires a control panel, and check rotation direction on commissioning. Flanged discharge — order the QD-65 coupling or a flange adaptor with the pump. Not for potable water or corrosive fluids (see Stainox range). Single-phase site? The 65-200 230V is the largest single-phase DN65. For more see the 65-400 (3 kW, 1,000 L/min, 20 m).

Technical specifications

Model	Evak Hippo 65-300 (HIPPO-300 DN65), 400V
Series	Evak Hippo DN — 2.5″ full free passage submersible sewage pump
Voltage / phase	400V three-phase, 50 Hz
Motor output	2.2 kW (3 HP)
Full load current	6 A
Poles / speed	2 pole / 2850 rpm
Operation	Manual (no float switch)
Discharge	DN65 (2.5″) flanged, DIN PN10/16
Free passage	65 mm
Rated duty	300 L/min @ 12.6 m
Max head	17 m
Max flow rate	870 L/min
Max liquid temperature	40 °C
Max submersion depth	10 m
Max starts per hour	20
Protection / insulation	IP68 / Class F
Thermal protection	Auto-reset thermal protector
Bearings	Ball type
Impeller	Recessed vortex
Pump casing	FC200 cast iron
Motor housing	Stainless steel
Mechanical seal	EKK Eagle Burgmann double mechanical, upper Ca/Ce, lower SiC/SiC, oil bath with NBR lip seal
Guide rail coupling	QM-65 / QD-65 (sold separately)
Cable	H07RN-F, 10 m
Overall height	630 mm
Weight (without cable)	34 kg

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.

Frequently Asked Questions

Quick answers to common questions about the Evak Hippo 65-300 2.2kW DN65 Sewage Pump 400V. For technical specifications, see the product details above; for sizing or installation advice, contact our team. If you have any other questions, we're happy to help.

What is a submersible pump?

A submersible pump is designed to operate fully submerged in the liquid it is moving. The motor is sealed inside the pump body and cooled by the surrounding water. Submersibles are used for drainage, sewage, septic tanks, deep wells and boreholes, and for raising water from sumps, cellars and floodwater. Many stocked at Anglian Pumping handle solids in suspension.

Can submersible pumps handle solids and sewage?

Yes – some submersibles are designed for clean water only, others handle solids up to 50 mm or full raw sewage. Anglian Pumping stocks ABS, BBC, Flygt and T-T Submersibles ranges that include vortex, single channel and grinder impellers for different solids handling requirements. Always match the pump to the maximum solid size and the type of effluent it will see.

When should I use a submersible pump instead of a surface pump?

Use a submersible when the water level is more than around 8 metres below the pump installation point – surface pumps cannot self-prime beyond that depth. Submersibles are also better when the liquid contains solids, when noise must be minimised, or when the pump needs to operate in confined spaces such as sumps and chambers where a surface pump would not fit.