Evak Hippo 80-550T 4.1kW DN80 Sewage Pump 400V

Name: Evak Hippo 80-550T 4.1kW DN80 Sewage Pump 400V
Brand: EVAK
SKU: evakhippo80-550T
Price: 1436.4 GBP
Availability: InStock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

The Evak Hippo 80-550T is the flagship of the Hippo DN80 range and the biggest pump in the Hippo family — 4.1 kW / 5.5 HP three-phase, recessed vortex impeller, 76 mm free passage and a DN80 flanged discharge for guide rail installation. 1,350 L/min and 18.5 m of head, rated 900 L/min at 8 m. The most volume and the most solids of any Hippo, with enough lift for a serious rising main.

Built for the largest stations the range serves: developments, industrial sites, hotels and treatment works with high inflow and unscreened solids. Cast iron pump body, stainless steel motor housing, EKK Eagle Burgmann double mechanical seal. Manual operation for panel control. 10 m cable.

4.1 kW

Motor output

1,350 L/min

Max flow

18.5 m

Max head

76 mm

Free passage

400V three-phase
Manual operation
DN80 flanged
Guide rail ready
Eagle Burgmann seal
Flagship

Flagship DN80 — 5.5 HP, 9.1 A at 400V. Three-phase only. Needs a control panel with level control; DOL or star-delta start to suit the site. Flanged outlet for a QD-80 guide rail coupling. 51.9 kg — lifting gear required. Need more lift than 18.5 m? See the 65-550 (22.5 m, 65 mm passage).

Full Description

More about this product

Full Description

The Evak Hippo 80-550T is the top of the Hippo DN80 range and the largest pump Evak make under the Hippo name. The model code says it: 80 for the DN80 discharge, 550 for 5.5 HP, T for three-phase. A 4.1 kW 2-pole motor drives a recessed vortex impeller to 1,350 L/min and 18.5 m of head, with a rated duty of 900 L/min at 8 m. Against the 65-550 it gives up 4 m of head and gains 150 L/min and 11 mm of free passage — the trade for a station where what comes down the drain matters more than how far it has to go.

76 mm free passage is the largest in the Hippo family. Raw sewage carries rag, wipes and solids that wrap around a smaller impeller; the DN80 vortex design keeps the impeller recessed out of the flow so solids pass through the volute without touching it. The DN80 flanged discharge (DIN PN10/16) bolts to a QD-80 quick-discharge coupling for guide rail installation, so the pump lifts out for service without anyone entering the chamber.

Cast iron pump body and volute, stainless steel motor housing, and an EKK Eagle Burgmann double mechanical seal (carbon/ceramic upper, silicon carbide lower) in an oil bath with NBR lip seal. Class F insulation, IP68, auto-reset thermal protector, ball bearings. Three-phase motor drawing 9.1 A, no capacitor, no float — supplied manual for control from a panel. 10 m cable. 51.9 kg — davit or hoist only.

Key features

4.1 kW

Motor output

5.5 HP

Horsepower

9.1 A

FLA @ 400V

DN80

Flanged discharge

76 mm

Free passage

1,350 L/min

Max flow

18.5 m

Max head

51.9 kg

Weight

Performance

Flow (L/min)	0	200	400	600	800	900	1000	1200	1350
Head (m)	18.5	17.0	14.8	12.3	9.5	8.0	6.8	4.6	3.0

50 Hz, 2850 rpm. 900 L/min @ 8 m is the Evak rated duty point; other values read from the published curve.

Construction

76 mm vortex impeller

Recessed vortex design passes 76 mm solids and rag through the volute without contact — the largest free passage in the Hippo family.

DN80 flanged discharge

DIN PN10/16 flange for a QD-80 quick-discharge coupling on a guide rail, or direct to a flanged riser. Lift out for service without entering the chamber.

Cast iron pump body

FC200 cast iron volute and casing for long life in raw sewage.

Stainless motor housing

Stainless steel motor housing over a Class F dry-type motor with auto-reset thermal protector and ball bearings. IP68.

EKK Eagle Burgmann double seal

Carbon/ceramic upper and silicon carbide lower mechanical seals in an oil bath with NBR lip seal — a named, serviceable seal set, not a generic one.

Three-phase manual motor

400V three-phase, 9.1 A, no capacitor, no float — wired to a control panel with level probes or floats. DOL or star-delta start to suit the supply.

Applications

Large pump stations

Duty/standby sewage chambers for housing developments, apartment blocks, hotels, schools and industrial estates.

High-inflow, high-solids sites

1,350 L/min with 76 mm passage — caravan parks, event venues and care homes where volume and rag arrive together.

Commercial rising mains

18.5 m of head covers most commercial pumped mains without stepping down to a 65 mm pump.

Treatment works transfer

Raw influent and sludge transfer on small municipal and larger packaged treatment plants.

Replacement duty

Direct swap for existing DN80 guide rail pumps — check the coupling, rail centres and panel rating before ordering.

Maximum liquid temperature 40 °C. Maximum submersion 10 m. Maximum 20 starts per hour. Manual operation — no float switch fitted. Three-phase only; requires a control panel rated for 9.1 A per pump, and check rotation direction on commissioning. 51.9 kg — use rated lifting gear. Flanged discharge — order the QD-80 coupling or a flange adaptor with the pump. Not for potable water or corrosive fluids (see Stainox range). For more head at 65 mm passage see the Hippo 65-550 (22.5 m).

Technical specifications

Model	Evak Hippo 80-550T (HIPPO-550 DN80), 400V
Series	Evak Hippo DN — 3″ full free passage submersible sewage pump
Voltage / phase	400V three-phase, 50 Hz
Motor output	4.1 kW (5.5 HP)
Full load current	9.1 A
Poles / speed	2 pole / 2850 rpm
Operation	Manual (no float switch)
Discharge	DN80 (3″) flanged, DIN PN10/16
Free passage	76 mm
Rated duty	900 L/min @ 8 m
Max head	18.5 m
Max flow rate	1,350 L/min
Max liquid temperature	40 °C
Max submersion depth	10 m
Max starts per hour	20
Protection / insulation	IP68 / Class F
Thermal protection	Auto-reset thermal protector
Bearings	Ball type
Impeller	Recessed vortex
Pump casing	FC200 cast iron
Motor housing	Stainless steel
Mechanical seal	EKK Eagle Burgmann double mechanical, upper Ca/Ce, lower SiC/SiC, oil bath with NBR lip seal
Guide rail coupling	QD-80 (sold separately)
Cable	H07RN-F, 10 m
Overall height	685 mm
Weight (without cable)	51.9 kg

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.

Frequently Asked Questions

Quick answers to common questions about the Evak Hippo 80-550T 4.1kW DN80 Sewage Pump 400V. For technical specifications, see the product details above; for sizing or installation advice, contact our team. If you have any other questions, we're happy to help.

What is a submersible pump?

A submersible pump is designed to operate fully submerged in the liquid it is moving. The motor is sealed inside the pump body and cooled by the surrounding water. Submersibles are used for drainage, sewage, septic tanks, deep wells and boreholes, and for raising water from sumps, cellars and floodwater. Many stocked at Anglian Pumping handle solids in suspension.

Can submersible pumps handle solids and sewage?

Yes – some submersibles are designed for clean water only, others handle solids up to 50 mm or full raw sewage. Anglian Pumping stocks ABS, BBC, Flygt and T-T Submersibles ranges that include vortex, single channel and grinder impellers for different solids handling requirements. Always match the pump to the maximum solid size and the type of effluent it will see.

When should I use a submersible pump instead of a surface pump?

Use a submersible when the water level is more than around 8 metres below the pump installation point – surface pumps cannot self-prime beyond that depth. Submersibles are also better when the liquid contains solids, when noise must be minimised, or when the pump needs to operate in confined spaces such as sumps and chambers where a surface pump would not fit.