Evak Hippo 80-150 1.1kW DN80 Sewage Pump 230V

Name: Evak Hippo 80-150 1.1kW DN80 Sewage Pump 230V
Brand: EVAK
SKU: evakhippo80-150230
Price: 612 GBP
Availability: InStock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

The Evak Hippo 80-150 (230V) is the entry point to the Hippo DN80 range — a 3″ sewage pump with 76 mm free passage and a DN80 flanged discharge for guide rail installation. 1.1 kW / 1.5 HP single-phase motor, recessed vortex impeller, up to 630 L/min and 7 m of head. Same motor as the 65-150; bigger volute, bigger solids, more flow, less lift.

Built for raw sewage and heavy wastewater where the solids are the problem rather than the head — short rising mains, big chambers, sites with a history of blockages. The 76 mm passage takes what a 65 mm pump won’t. Cast iron pump body, stainless steel motor housing, EKK Eagle Burgmann double mechanical seal. Internal capacitor and 10 m cable; float switch available.

1.1 kW

Motor output

630 L/min

Max flow

7 m

Max head

76 mm

Free passage

230V single-phase
DN80 flanged
Guide rail ready
Vortex impeller
Eagle Burgmann seal
IP68

Entry-level DN80 — 1.5 HP, 230V. Low head: 7 m maximum. Check the rising main before choosing this over the 65-150 (11 m) — the 80 is for solids and volume, not lift. Flanged outlet for a QD-80 guide rail coupling or flanged riser, not a hose tail. Also available as the Hippo 80-150 400V. For more head see the 80-200 (9 m) or 80-300T (13 m).

Full Description

More about this product

Full Description

The Evak Hippo 80-150 (230V) is the smallest pump in the Hippo DN80 range. The model code says it: 80 for the DN80 discharge, 150 for 1.5 HP. It shares its 1.1 kW single-phase motor with the 65-150, but the 3″ volute changes what that motor does: 76 mm free passage, 630 L/min, and a maximum head of 7 m, rated 415 L/min at 4.4 m. It’s a flow-and-solids pump, not a lift pump — the right choice for a chamber close to the sewer with a history of blockages.

76 mm free passage is the largest in the Hippo family. Raw sewage carries rag, wipes and solids that wrap around a smaller impeller; the DN80 vortex design keeps the impeller recessed out of the flow so solids pass through the volute without touching it — and at 76 mm, almost nothing that comes down a domestic or commercial drain will stop. The DN80 flanged discharge (DIN PN10/16) bolts to a QD-80 quick-discharge coupling for guide rail installation, so the pump lifts out for service without anyone entering the chamber.

Cast iron pump body and volute, stainless steel motor housing, and an EKK Eagle Burgmann double mechanical seal (carbon/ceramic upper, silicon carbide lower) in an oil bath with NBR lip seal. Class F insulation, IP68, auto-reset thermal protector, ball bearings. Internal capacitor, 10 m cable. Supplied manual; a float switch version is available for automatic single-pump duty. 40.4 kg — the larger volute adds 10 kg over the 65-150, so plan on lifting gear.

Key features

1.1 kW

Motor output

1.5 HP

Horsepower

10 A

FLA @ 230V

DN80

Flanged discharge

76 mm

Free passage

630 L/min

Max flow

7 m

Max head

40.4 kg

Weight

Performance

Flow (L/min)	0	100	200	300	415	500	630
Head (m)	7.0	6.5	5.9	5.2	4.4	3.8	3.0

50 Hz, 2850 rpm. 415 L/min @ 4.4 m is the Evak rated duty point; other values read from the published curve.

Construction

76 mm vortex impeller

Recessed vortex design passes 76 mm solids and rag through the volute without contact — the largest free passage in the Hippo family.

DN80 flanged discharge

DIN PN10/16 flange for a QD-80 quick-discharge coupling on a guide rail, or direct to a flanged riser. Lift out for service without entering the chamber.

Cast iron pump body

FC200 cast iron volute and casing for long life in raw sewage.

Stainless motor housing

Stainless steel motor housing over a Class F dry-type motor with auto-reset thermal protector and ball bearings. IP68.

EKK Eagle Burgmann double seal

Carbon/ceramic upper and silicon carbide lower mechanical seals in an oil bath with NBR lip seal — a named, serviceable seal set, not a generic one.

Single-phase with internal capacitor

Start capacitor built into the motor — no external box. Runs from a panel or, with the float switch option, on its own.

Applications

Blockage-prone stations

Chambers with a history of ragging on 50 or 65 mm pumps — care homes, pubs, holiday parks — where the fix is passage, not power.

Short rising mains

Pump stations close to the sewer connection with modest lift, where 7 m is plenty and flow matters more.

Large-volume chambers

Big wet wells and balancing tanks that need emptying fast rather than pumped far.

Treatment plant transfer

Raw influent transfer between tanks at low head, where the inflow is unscreened.

Replacement duty

Direct swap for existing DN80 guide rail pumps — check the coupling and rail centres before ordering.

Maximum liquid temperature 40 °C. Maximum submersion 10 m. Maximum 20 starts per hour. Maximum head 7 m. Size the rising main carefully — for more lift at the same solids size see the 80-200 (9 m) or 80-300T (13 m); for more lift at 65 mm see the 65-150 (11 m). Flanged discharge — order the QD-80 coupling or a flange adaptor with the pump. Supplied manual; specify the float switch version for automatic single-pump duty. Not for potable water or corrosive fluids (see Stainox range). Three-phase site? See the Hippo 80-150 400V.

Technical specifications

Model	Evak Hippo 80-150 (HIPPO-150 DN80), 230V
Series	Evak Hippo DN — 3″ full free passage submersible sewage pump
Voltage / phase	230V single-phase, 50 Hz
Motor output	1.1 kW (1.5 HP)
Full load current	10 A
Starting	Internal capacitor
Poles / speed	2 pole / 2850 rpm
Operation	Manual (float switch version available)
Discharge	DN80 (3″) flanged, DIN PN10/16
Free passage	76 mm
Rated duty	415 L/min @ 4.4 m
Max head	7 m
Max flow rate	630 L/min
Max liquid temperature	40 °C
Max submersion depth	10 m
Max starts per hour	20
Protection / insulation	IP68 / Class F
Thermal protection	Auto-reset thermal protector
Bearings	Ball type
Impeller	Recessed vortex
Pump casing	FC200 cast iron
Motor housing	Stainless steel
Mechanical seal	EKK Eagle Burgmann double mechanical, upper Ca/Ce, lower SiC/SiC, oil bath with NBR lip seal
Guide rail coupling	QD-80 (sold separately)
Cable	H07RN-F, 10 m
Overall height	615 mm
Weight (without cable)	40.4 kg

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.

Frequently Asked Questions

Quick answers to common questions about the Evak Hippo 80-150 1.1kW DN80 Sewage Pump 230V. For technical specifications, see the product details above; for sizing or installation advice, contact our team. If you have any other questions, we're happy to help.

What is a submersible pump?

A submersible pump is designed to operate fully submerged in the liquid it is moving. The motor is sealed inside the pump body and cooled by the surrounding water. Submersibles are used for drainage, sewage, septic tanks, deep wells and boreholes, and for raising water from sumps, cellars and floodwater. Many stocked at Anglian Pumping handle solids in suspension.

Can submersible pumps handle solids and sewage?

Yes – some submersibles are designed for clean water only, others handle solids up to 50 mm or full raw sewage. Anglian Pumping stocks ABS, BBC, Flygt and T-T Submersibles ranges that include vortex, single channel and grinder impellers for different solids handling requirements. Always match the pump to the maximum solid size and the type of effluent it will see.

When should I use a submersible pump instead of a surface pump?

Use a submersible when the water level is more than around 8 metres below the pump installation point – surface pumps cannot self-prime beyond that depth. Submersibles are also better when the liquid contains solids, when noise must be minimised, or when the pump needs to operate in confined spaces such as sumps and chambers where a surface pump would not fit.