Name: Grundfos TPE3 D 50-180-S A-F-A-BQQE 99272555
Brand: Grundfos
SKU: 99272555
Price: 7229.3 GBP
Availability: InStock

Grundfos TPE3 D 50-180-S A-F-A-BQQE 99272555

In stock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

Grundfos TPE3 D 50-180-S cast iron 400V twin-head in-line pump

Twin-head, close-coupled in-line circulator with two identical power heads on a common cast iron housing. Each head carries an IE5 permanent-magnet motor with its own frequency converter, and the pair runs duty/standby with automatic alternation or in duty-assist at peak load.

TPE3 is factory fitted with a combined differential-pressure and temperature sensor, so it runs closed-loop control straight out of the box — no separate transducer to buy or wire.

DN 50

Connection

1.1 kW

Motor

3 x 400V

Supply

IE5

Efficiency

Built-in ΔP + temp sensorAUTOADAPTFLOWADAPTHeat energy monitorTop-pull-outDuty/standby

Three-phase 400V supply. The single-phase 230V version is listed separately — check your supply before ordering.

Full Description

More about this product

Full Description

Applications

Heating and district heating systems
Air conditioning and chilled water systems
Ground-source and air-source heat pump systems
Industrial process and cooling circuits
Domestic hot water and secondary circulation
Solar thermal systems

Specification

Model	TPE3 D 50-180-S
Grundfos type key	TPE3 D 50-180 S-A-F-A-BQQE-GYC
Configuration	Twin head, two parallel power heads
Nominal connection	DN 50, DIN flanges to EN 1092-2
Rated motor power (P2)	1.1 kW per head
Supply voltage	3 x 400 V, 50 Hz
Motor	Permanent-magnet synchronous, fan-cooled, IE5 to IEC 60034-30-2
Speed control	Integrated frequency converter and PI controller
Sensor	Factory-fitted combined differential-pressure and temperature sensor
Pump housing	Cast iron EN-JL1040
Shaft seal	BQQE rubber bellows seal (SiC/SiC/EPDM) to EN 12756
Liquid temperature	-25 °C to +120 °C
Enclosure	IP55, insulation class F
Design	Top-pull-out, in-line

Key features

Built-in sensor

The combined differential-pressure and temperature sensor is fitted at the factory, so closed-loop control needs no extra transducer, cabling or set-up.

IE5 permanent-magnet motor

Exceeds the IE5 threshold of IEC 60034-30-2, with materially lower running cost than an equivalent fixed-speed induction pump.

Heat energy monitoring

Flow and temperature readings let the pump estimate heat energy delivered — useful for balancing, commissioning and spotting system faults.

Top-pull-out servicing

Motor, pump head and impeller lift out as one assembly while the housing stays in the pipework.

Duty and standby built in

The heads alternate automatically to share running hours; the standby head starts on fault, and both can run together for peak demand.

Grundfos GO

Commission, read status and change set points from a phone or tablet with the Grundfos GO app.

Control modes

AUTOADAPT	Default. The pump finds the lowest workable proportional-pressure curve for the system and keeps adjusting it.
FLOWADAPT	AUTOADAPT with a maximum flow limit — useful where flow must not exceed a design figure.
Proportional pressure	Head falls as flow falls. Suits radiator and two-pipe heating systems with thermostatic valves.
Constant pressure	Holds a fixed differential pressure regardless of flow. Suits underfloor heating and systems with low pipe losses.
Constant temperature	Controls speed to hold a set liquid temperature, e.g. domestic hot water return.
Constant curve	Fixed speed set from the control panel, Grundfos GO or an external signal.

Frequently asked questions

Do I need to buy a pressure sensor?

No. TPE3 pumps have a combined differential-pressure and temperature sensor fitted at the factory, so proportional-pressure, constant-pressure and AUTOADAPT control work without any extra parts.

What is the difference between TPE2 and TPE3?

Both use IE5 permanent-magnet motors with integrated speed control. TPE2 has no sensor and needs an external transducer for closed-loop control; TPE3 has the sensor built in and adds heat energy monitoring.

Is this the single-head or twin-head version?

Twin head. The single-head equivalent is the TPE3 50-180, which we list separately.

What supply does it need?

3 x 400 V, 50 Hz. We list the 400V three-phase and 230V single-phase versions as separate products, so check the supply before ordering.

Downloads

manual PNG
Download
Data Sheet PDF
Download

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.