EVAK puddle sucker pumps
EVAK puddle sucker pumps RESIDOX 750-110v
- Established 1975
- Trusted by thousands of customers
The Evak Residox 750 (110V) is the higher-output manual puddle sucker pump in the Residox range, built for larger flood areas, longer hose runs and applications where water needs moving over distance or discharged uphill. It shares the Residox 400’s low-level pumping down to 1mm, with significantly more capacity behind it.
- Highest flow rate in the Residox range
- Stainless steel case, cast iron housing, Hytrel vortex impeller
- Manual operation, no priming required
- 110V – suited to site use via a transformer
More about this product
Overview
The EVAK Residox 750 (110V) is the higher-output ultra-low-level manual puddle pump in the Residox range, built for larger flood areas, longer hose runs, and applications where water needs to be moved over distance or discharged uphill. It is the highest flow rate puddle pump in the range, sharing the construction and low-level pumping characteristics of the Residox 400, with significantly more capacity behind it.
When to Choose the 750 Over the 400
The 750 is the appropriate choice when flow rate matters more than cost. It delivers 330 litres per minute and a maximum head of 16 metres, against 250 l/min and 11m on the Residox 400, clearing larger volumes faster and pumping further from the source.
For straightforward domestic flooding and standard nuisance water, the Residox 400 is usually sufficient.
Ultra-Low-Level Pumping
The Residox is designed for jobs that conventional submersible pumps cannot finish. Where a standard pump stops drawing once the water drops below its inlet, the Residox continues pumping down to approximately 1mm above the floor, leaving surfaces almost dry. That makes it well suited to flood recovery, basement clearance and any application where minimal residual water is the priority.
Key Features
Performance at a Glance
Technical Specification
| Voltage | 110V |
| Motor rating | 750W (0.75HP), 2850 RPM |
| Current draw | 5.4A |
| Max flow | 330 litres/min |
| Max head | 16 metres |
| Free passage | 2mm |
| Discharge | 2″ hosetail |
| Seal | Double mechanical seal, SIC/SIC, oil chamber |
| Cable | 10m H07RN-F |
| Housing materials | Cast iron pump housing, stainless steel outer case and handle, alloy motor and seal casing |
| Weight | 17.8kg |
| Warranty | 12 months |
No Priming Needed
Unlike some other puddle pumps (such as the Tsurumi LSC range), the Residox does not need to be primed with water poured into the pump body. Place it down in the water to be removed, switch it on, and pump. The pump is fully submersible and should always be operated submerged or with water present at the suction base, and should not be left to run dry.
What’s in the Box
- 1 x EVAK Residox 750 Manual Puddle Pump
- 1 x 10m heavy-duty rubber power cable
- 1 x 2 inch (50mm) hose tail
FAQs
The 750 delivers more flow (330 l/min vs 250 l/min) and head (16m vs 11m), so it’s the better choice for larger floods, longer hose runs or uphill discharge. For straightforward domestic flooding, the Residox 400 is usually sufficient.
110V is the standard site-safety voltage, run via a transformer – suited to construction sites and hire fleet use rather than domestic mains.
No – simply place it in the water and switch on.
Yes – the 2mm free passage and Hytrel vortex impeller are built for dirty, debris-laden flood conditions.
Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.
Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).
Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.
Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.
Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.
Related products
Lowara DOC Pumps Submersible pumps for drainage, infiltration water and emptying of pools, ponds, tanks and reservoirs. The DOC pump is mainly made of stainless…
The KP range of pumps from Grundfos is suitable for both temporary and permanent free-standing installation, as well as installation within a collecting tank. Easy-to-install,…
The Clarke PVP11A stainless steel pump ideal for heavy duty draining applications including pits, sumps, ditches, fottings etc. It can be used to remove both…
The Clarke CSD3 multi-stage 4 impeller pump is for use with cold, clean water i.e. wells or rain water tanks and can pump up to…
DOMO series, stainless steel electric pumps, are available with twin-channel or vortex impeller (DOMO VX). Designed to handle suspended solids up to 50mm in diameter…
The Clarke PSD1A stainless steel pump designed to clear water from ponds and pools. Suitable for operating waterfalls, fountains, irrigating gardens and draining cellars. Includes a…
Frequently Asked Questions
Quick answers to common questions about the EVAK puddle sucker pumps RESIDOX 750-110v. For technical specifications, see the product details above; for sizing or installation advice, contact our team. If you have any other questions, we're happy to help.
What is a submersible pump?
A submersible pump is designed to operate fully submerged in the liquid it is moving. The motor is sealed inside the pump body and cooled by the surrounding water. Submersibles are used for drainage, sewage, septic tanks, deep wells and boreholes, and for raising water from sumps, cellars and floodwater. Many stocked at Anglian Pumping handle solids in suspension.
Can submersible pumps handle solids and sewage?
Yes – some submersibles are designed for clean water only, others handle solids up to 50 mm or full raw sewage. Anglian Pumping stocks ABS, BBC, Flygt and T-T Submersibles ranges that include vortex, single channel and grinder impellers for different solids handling requirements. Always match the pump to the maximum solid size and the type of effluent it will see.
When should I use a submersible pump instead of a surface pump?
Use a submersible when the water level is more than around 8 metres below the pump installation point – surface pumps cannot self-prime beyond that depth. Submersibles are also better when the liquid contains solids, when noise must be minimised, or when the pump needs to operate in confined spaces such as sumps and chambers where a surface pump would not fit.