Name: Ebara Matrix 5-9T/2.2M 230v 2470590000E
Brand: Ebara
SKU: 2470590000E
Price: 775.2 GBP
Availability: InStock

In stock

Any questions? Message us on WhatsApp

Established 1975
Trusted by thousands of customers

The Ebara Matrix 5-9T/2.2M is a compact horizontal multistage centrifugal pump with nine stages, built in AISI 304 stainless steel. The pump is close-coupled to a 2.2 kW single-phase IE2 motor with built-in capacitor and thermal overload, and the standard carbon / ceramic / EPDM seal is WRAS approved for drinking water.

It covers 1.8 to 7.8 m³/h on Ebara’s selection chart, with around 104 m of head at shut-off. It suits pressure boosting, water supply and transfer, irrigation, washdown and light industrial duties, and connects through a G1¼ suction and a G1 discharge.

7.8 m³/h

Max flow

104 m

Max head (shut-off)

2.2 kW

IE2 motor

10 bar

Max working pressure

65 dB(A)

Sound level at 1 m

230 V single phase
AISI 304 stainless
G1¼ / G1 connections
IP55
WRAS-approved seal
IE2 motor

Bare pump: it needs a pressure switch, flow controller or inverter to start and stop it, and must be filled with water before first start and never run dry. Shut-off is around 10.2 bar, just above the 10 bar maximum working pressure, so feed it from a break tank rather than the mains.

Full Description

More about this product

Full Description

Ebara Matrix 5-9T/2.2M Overview

The Matrix 5-9T/2.2M is the nine-stage model in Ebara’s Matrix 5 range of horizontal multistage pumps, with a 230 V single-phase motor. The casing, impellers, intermediate stages, casing cover and wetted shaft are all AISI 304 stainless steel, and the motor has a built-in run capacitor and thermal overload, so it can be wired straight to a protected 230 V supply.

It delivers from 1.8 m³/h up to 7.8 m³/h, with around 104 m of head at shut-off and 39.6 m at 7.8 m³/h. It is quiet and compact, which suits domestic and commercial pressure boosting, water supply and transfer, irrigation, rainwater reuse, washdown and light industrial use. As a bare pump it needs a pressure switch, flow controller or inverter to run it as a booster.

Key Features

Nine-stage Matrix 5 hydraulics

97 mm closed impellers giving around 104 m at shut-off and up to 7.8 m³/h.

All-stainless wetted parts

AISI 304 casing, impellers, intermediate stages, casing cover and shaft, with an AISI 304 / PPS liner ring. Suitable for water with up to 500 ppm chlorine.

2.2 kW IE2 motor

2.2 kW (3.0 HP) TEFC two-pole motor, 230 V single phase, 12.3 A, IE2, IP55, Class F insulation, with built-in capacitor and thermal overload.

WRAS-approved seal

The standard carbon / ceramic / EPDM mechanical seal is WRAS and DM174/2004 approved for drinking water, for liquids from −15 to +85 °C.

Quiet running

Around 65 dB(A) at 1 m (±2.5 dB), so it can be installed indoors in plant rooms and utility areas.

Compact horizontal design

627 mm long and 28.5 kg, with threaded G1¼ suction and G1 discharge, and the motor bracket in die-cast aluminium.

Technical Specifications

Specification	Value
Model	Ebara Matrix 5-9T/2.2M
Ebara part number	2470590000E
Pump	Horizontal multistage centrifugal, 9 stages, 2-pole
Flow range (selection chart)	1.8–7.8 m³/h
Head at minimum / maximum flow	97 m / 39.6 m
Shut-off head	approx. 104 m (10.2 bar)
Maximum working pressure	1 MPa (10 bar)
Impeller diameter	97 mm
Suction / discharge	G1¼ F / G1 F, threaded (ISO 228)
Motor	2.2 kW (3.0 HP), IE2, TEFC, 2-pole, 2850 rpm
Supply	230 V ±10% single phase, 50 Hz
Full load / locked rotor current	12.3 A / 73.0 A at 230 V
Capacitor	55 µF 450 V, built in
Overload protection	Built-in thermal overload
Protection / insulation	IP55 / Class F
Sound level	65 dB(A) at 1 m (±2.5 dB)
Liquid temperature	−15 to +85 °C with the standard seal
Max ambient temperature	40 °C
Bearings (pump / fan side)	6305 / 6205
Cable entry	M20x1.5
Weight	28.5 kg
Test standard	ISO 9906:2012 Grade 3B

Performance

Duty points at 50 Hz from Ebara’s Matrix selection chart (ISO 9906:2012 Grade 3B, clean water at 20 °C).

Flow (m³/h)	0	1.8	2.7	3.6	4.8	6	7.8
Head (m)	104	97	92	87	78	66	39.6

Materials

Component	Material
Pump casing, casing cover	EN 1.4301 (AISI 304)
Impellers, intermediate casings	EN 1.4301 (AISI 304)
Shaft	EN 1.4301 (AISI 304), wet extension
Liner ring	EN 1.4301 (AISI 304) + PPS
Mechanical seal	Carbon rotary / ceramic stationary faces, EPDM gasket and bellows, EN 1.4402 (AISI 316) spring, frame and retainer
O-rings	EPDM
Motor bracket	Die-cast aluminium
Motor casing	Aluminium

Dimensions and Weight

Dimension	Value
Overall length	627 mm
Overall height	231 mm
Base width / fixing centres	170 mm / 125 × 140 mm, Ø9 mm holes
Weight	28.5 kg
Suction / discharge	G1¼ / G1

Installation Notes

Supply: 230 V single phase, 12.3 A full load and 73.0 A locked rotor. The capacitor and thermal overload are built in. Wire through a suitable isolator and protective device; electrical installation must be carried out by a qualified electrician.

Priming and dry running: Before first start, remove the priming plug on the pump casing near the discharge, fill the pump with water until it overflows, refit the plug and run at full flow for a few minutes. The pump must never run dry, and Ebara advises against running below 10% of best-efficiency flow, so avoid running for long against a closed valve.

Pressure: Shut-off is around 10.2 bar and the maximum working pressure is 10 bar. Inlet pressure plus pump pressure must not exceed 10 bar. With this pump that leaves effectively no allowance for inlet pressure, so feed it from a break tank.

Location: Install indoors or under cover with the shaft horizontal, at no more than 40 °C ambient, and protect it from frost. Support the pipework so no load is carried by the pump connections.

Frequently Asked Questions

What does the code Matrix 5-9T/2.2M mean?

Matrix 5 = the Matrix range sized for around 5 m³/h at best efficiency; 9 = number of impellers; T = threaded pipe connections; 2.2 = motor size in kW; M = single-phase motor.

Is it approved for drinking water?

Yes. The standard version with the carbon / ceramic / EPDM seal is WRAS and DM174/2004 (ICIM) approved for drinking water, for liquids up to 85 °C.

Will it switch itself on and off?

No. This is a bare pump, so it needs a pressure switch, flow controller or inverter to start and stop it on demand. For a ready-made variable speed booster with the same Matrix 5-9T pump end, see the 1GPE MATRIX 5-9T/2.2 ESPM (part 2002470106), which runs from 230 V single phase.

Is there a three-phase version?

Yes. The Ebara Matrix 5-9T/2.2 (part 2470590004I) has the same pump end with a 2.2 kW IE3 230/400 V three-phase motor.

What if I need less head?

For less head, the eight-stage Matrix 5-8T/2.2M gives around 92 m at shut-off on a 2.2 kW motor. All Matrix 5 models cover up to 7.8 m³/h.

Can it pump hot water?

The standard seal is rated for −15 to +85 °C. Ebara makes -TE and special-seal versions for up to 110 °C, but these are different part numbers, so ask us before ordering for hot-water duties.

Is there an insulation jacket?

Yes. Ebara supplies a body insulation casing for this pump, part 341445041, for chilled or heated water duties. Ask us to add it to your order.

Downloads

Data Sheet PDF
Download

Delivery Information

Standard delivery:
Standard delivery is free on most orders. Some items may incur a delivery charge depending on weight, size or value. Any applicable charge will be displayed at checkout.

Deliveries will typically be made between 7am and 6pm, Monday to Friday (excluding public holidays).

Next day delivery:
Next working day delivery is available for a £16.50 + VAT delivery charge.

Orders must be placed before 12 noon to qualify for next working day delivery. Orders placed after 12 noon on Thursday but before noon on Friday will be delivered the following Monday. Orders placed after 12 noon on Friday will be delivered on Tuesday.

Pallet/Large/Difficult items:
Some large, heavy or difficult to transport items may incur an additional delivery charge. Please contact us for a delivery quote before ordering.